home-banner-1 home-banner-2 home-banner-3 home-banner-4 home-banner-5
contact-us

REPAIRS MADE AS EASY AS 1.2.3.

3 Styles Available To Fit Your Need

General Repair Patches - Fixes Breaks, Cracks, and Holes

Rugged Repair Patches - Fixes Breaks, Cracks, and Holes & Tough Against Impact and Abrasion

Structural Repair Patches - Fixes Breaks, Cracks, and Holes with Additional Reinforcement

How the Patches Work

For best results, clean the damaged area first. (Alcohol is recommended.) For best adhesion, damaged area should be dry and free of dirt and debris.  For low surface energy repair applications an adhesive primer applied after cleaning will enhance bonding. (Available from PatchNRepair).

stackedpatches

1. Heat the patch to approximately 194 °F (90 °C) using an appropriate heating method. Heating methods can be MRE heater (included with kits), oven, not used for food due to possible out gassing, wrapped in foil to protect paper backing, or heat gun. When using a heat gun, do not place the heat gun too close to the patch surface or hold heat in one place for more than a few seconds. Warning: DO NOT HEAT ABOVE 270 °F (132 °C). Be sure your heating method complies with safety standards according to the conditions under which you will be applying the patch– for example, outdoors, in rainy weather, near flammable materials, etc.

2. Once the temperature is near or above 194 °F (90 °C), the material will soften and become very flexible. While heated, the patch can easily be cut to shape with scissors. Be sure to leave at least 1 inch of material on all sides of a hole or crack to improve adhesion and structural results. While wearing gloves that protect against the heat, remove and discard the film backing from the patch. Avoid touching the adhesive once the film backing is removed.

3. Press from one end of the patch to the other, applying pressure to shape it and press it into the contours of the repair surface. Continue pressing and shaping until it cools and becomes rigid again. Cooling time depends on the temperature of the damaged surface and on ambient air temperature, but normally the patch cools and becomes rigid again within one to two minutes.

Note: Do not heat with a direct flame or contact the patch directly with a heating surface that is over 270 °F (132 °C). Do not store in direct sunlight. Not for use on pressurized tanks or lines. Avoid contact of the adhesive with skin. Removal may damage painted and gel-coated surfaces. Not warranted for any specific application.

EXCEPT FOR SUCH EXPRESS WRITTEN WARRANTY, IF ANY, AS SPINTECH, LLC MAY ISSUE TO THE PURCHASER, SPINTECH, LLC MAKES NO WARRANTY, EXPRESS OR IMPLIED, WITH RESPECT TO ANY PRODUCT, INCLUDING, BUT NOT BY WAY OF LIMITATION, THE MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE OF SUCH PRODUCT.

Any and all statements, technical information, and recommendations provided by Seller to Buyer are based on tests believed to be reliable at the time of purchase, but the accuracy or completeness thereof is not guaranteed. Seller's and Manufacturer's only obligations shall be to replace such quantity if the product proved to be defective. Before using, Buyer shall determine the suitability of the product for its intended use and Buyer assumes all risk and liability whatsoever in connection therewith. In no event is any such suggestion or information to be considered or represented to be a recommendation or a final or preliminary engineering or other design. Seller shall have no obligations or liability whether on account or negligence or otherwise except other than as provided herein. Neither Seller nor Manufacturer shall be liable either in tort or in contract for any loss or damage, direct, incidental, or consequential arising out of the use or inability to use the product. The Purchaser assumes sole and full responsibility for being familiar with all characteristics of all products and for determining and satisfying itself as to the content of all products and the suitability of all products for the uses and applications contemplated by the Purchaser and others, as well as for complying with all laws, regulations and standards applicable to the possession, handling, processing, and use of all products.

PatchNRepair Uses PatchNRepair How To
Patch N Repair Uses Patch N Repair How To